High Polymer Adhesive Bandage

Location:
Jinan, China ( Mainland)
Status:
New
Sample Availibility:
yes
Payment Terms:
Cash, Bank Transfer, Letter of Credit, T/T, L/C
Categories:

Product Description

High Polymer Adhesive Bandage

[Material ]

The tape is made of multi-layer knitted fiberglass impregnated with water-activated polyurethane resin.

[Character & advantage]

1)Simple operation: Room temperature operation, short time, good molding feature

2) High hardness & light weight

20 times hard than plaster bandage; light material and use less than plaster bandage;

Its weight is plasters 1/5 and its width is plasters 1/3,which could reduce wound burden

3) lacunary (many holes structure) for excellent ventilation

Unique knitted net structure make sure good air ventilation and prevent skin damp and

hot & pruritus.

4) Rapid ossification (concretion)

It ossifies in 3-5 minutes after open the package and could bear weight after 20 minutes,

But plaster bandage need 24 hours for full concretion

5) Excellent X-ray penetration

Good x-ray penetration ability makes X-ray photo clearly without remove the bandage, but

plaster bandage need remove to make x-ray inspection.

6) Good waterproofing quality

The moisture -absorbed percent is 85% less than plaster bandage, Even the patient touch

the water situation, it still could keep dry in the injury position

7) Convenient operation & mold easily.

8) Comfortable & safe to patient/doctor

Material is friendly to operator and it wont become tension after concretion.

9) Wide application

10) Environment friendly

Material are environmental friendly, which could not produce polluted gas after

inflammation.

[How to use Cast](We have video in the website)

1) Put the pad (cotton coil or cotton slipcover) on the surgery position.

2) Wear surgical gloves.

3) Select proper specification according to the surgery position.

4) Immerse the roll in room temperature water(21-24°C) for 4-6 seconds and squeeze it 2-3 times firmly. If the water warmer than 21-24°C shortens the immersing time, while cooler than 21-24°C water lengthens the time.

5) Enwind spirally; Overlapping the previous layer by one-half or two-thirds of the roll width. To maintain proper tension is very important and take care to avoid excessive tightness. The strength can be determined by the number of layers used. Just 3-4 layers provide a string non-weigh-bearing cast and 5-6 layers are typically adequate for weight-bearing cast.

6) Additional after the initial enwinding should be overlapped on itself to achieve good molding. Enwind the roll in 3-5 minutes after immersing in water because after that time it will be concretion.

7) Smooth and rub the surface to achieve good contact between layers. Keeping smoothness helps mold the wrap.

Allow about 10 minutes for sufficient concretion and let patients not move during this time. It could bear electric weight after 20 minutes.

8) It could be windowed, trimmed or removed with traditional cast saw equipment.

Item number

Size

Package

Injury position

HCF002

5.0cmX 360cm

10 packX12box/ctn

Children’s hand, fingers &toes

HCF003

7.5cmX 360cm

10 packX12box/ctn

Children’s wrists, ankles, arms&leg

HCF004

10.0cmX 360cm

10 packX9box/ctn

Children’s leg & ankle, adult’s hand& wrist

HCF005

12.5cmX 360cm

10 packX9box/ctn

Adult’s arms and legs

HCF006

15.0cmX 360cm

10 packX9box/ctn

Adult’s arms and legs



This member's information has NOT been authenticated or verified by importexportleads.net or any third party. Only Gold Members have completed an authentication and verification procedure conducted by third-party credit agencies.

For more information on importexportleads Gold Membership, Click here

Contact Information

Company:
 Shandong Hardy Bone Medical Technology Co., Ltd.
Phone Number:
  86-0531-67867809
Fax Number:
 86-0531-67867807