2PLF series large capacity clay crusher for sale

Application Field and Working Principle:

2PLF Series grading teeth-roller Industrial Trituradora piedra is widely used for 1­st stage crushing, 2nd stage crushing and 3rd stage crushing in the crushing system in pit, workshop and openwork. This teeth-roller crusher is driven by electromotor via reducer, making two teeth-rollers rotate inward synchronously in opposite direction. After material dropping from the inlet to crushing chamber, it will be firstly classified; those which are accepted will enter into outlet chute through teeth-roller spacing. Then other massive materials are crushed through breaking, cutting, stretching between two teeth-rollers, and then discharged from outlet opening.

1.Initially,the material is ripped by the leading faces of opposed rotor teeth.These subject the rock to multiple point

loading ,in-ducing stress into the material to exploit any natural weaknesses.

2.At the second stage,material is broken in tension by being subjected to a three point loading, applied between the

front tooth faces on one rotor,and rear tooth faces on the rotors.

3.Any lumps of material that still remain oversize,are broken as the rotors chop through the fixed teeth of the breaker

bar,thereby achieving a three dimensional controlled product size.

The basic concept of the ZYM Crusher, is the use of two rotors with large teeth, on small diameter shafts, driven at

a low speed by a direct high torque drive system. This design produces three major principles which all interact

when breaking materials using Sizer Technology. The unique principles are; The Three-Stage Breaking Action,

The Rotating Screen Effect, and The Deep Scroll Tooth Pattern.

The current range of sizers is from 500 series to 1500 series and each sizer is specially manufactured to satisfy the project requirements. Below are the characteristics of an Zhenyuan sizer, which identify its design.

Centre Distance of Shafts

This is the measurement in millimetres, between the centre line of the two shafts. It is the main designation of an Zhenyuan sizer and is often referred to by the series number i.e. 500series sizer = 500mm centre distance(centres).

This distance combined with the tooth design and configuration controls the maximum size of infeed material that the unit can process efficiently.

Length of Inlet

The length of inlet is the length in millimetres of the sizing chamber.

The length of the inlet is a major factor in the volume of material that the unit can process.

Tooth Configuration

The tooth configuration in conjunction with a breaker bar, when fitted, controls the product size

Breaker Bar

The adjustable breaker bar, when fitted, is bolted underneath the shafts and can be moved up and down to add another stage to the breaking process. This is only fitted to 3/4tooth

Inward / Outward Shaft Rotation

Inward shaft rotation is the standard method of operation for most types of tooth configuration and must be used on wet/sticky materials.

Outward running is usually only employed on secondary machines for certain materials to produce a smaller product than is possible running inwards.

Breaker Combs

Breaker combs are static teeth which protrude from the side plate into the sizing chamber, and nestle between the sizing teeth. They are used when the shaft rotation is outward running, for the rotating teeth to chop through.

Cleaning Combs

These are specially shaped static teeth which also protrude from the side plate into the sizing chamber, and snuggly fit arround and between the sizing teeth. These are usually fitted in very wet and sticky situations, and act as a continuous cleaning system to prevent clogging of the teeth and optimise sizing efficiency. Cleaning combs can also act as reversing combs.

Reversing Combs

These are shaped static blocks which protrude from the side plate into the sizing chamber, and nestle between the sizing teeth. Reversing combs stop oversize material from passing through the sides of the machine and also in the event of reversing the shafts eliminate the problem of material being jammed between the side plate and the teeth

Control box:

Technical Data

Service

1. Pre-sale services
Act as a good adviser and assistant of clients; Enable them to returns on their investments.

2. Services during the sale

Respect clients; Devote ourselves to improving the total value

3. After-sale services
Provide considerate services to minimize clients' worries.

Our crusher be used in an underground coal mine:

There we supply a whole produce plant include the bunker,vibrating screen ,belt conveyor ,vibrating feeder and 2PLF coal grading crusher machine.

This mine is located in Henna ,China ,if you need when you come China ,we will take you to visit the site!

Photos from testing vedio:

Heavy duty processing equipments of Zhenyuan:

Workshop of Zhenyuan:

Welcome your inquiry! Please feel free to contact me for details!!