HCT2702A / HCT2702B Epoxy Paint

Product Type

Component A: HCT2702A

Component B: HCT2702B

Product Description

The product is two-component waterbased glossy epoxy varnish, which is applied to wood, cement (sand) mortar floor.

Product Highlights

l Transparent film with gloss.

l Excellent construction performance and levelling.

l Excellent adhesion and water resistance.

l High hardness, good impact resistance.

l Good decorative performance, high fullness.

l Water based and environmental product, which makes it a good choice for replacing solvent based products.

Technique Data

l Colour Transparent

l Solid Content 37.5±1%(Construction ratio A:B=3:1)

l Theoretic Coating Rate about 6-7 m²/kg (Flat surface, coat once. If the substrate is wood, coating at least twice is

suggested. Practical coating rate is different according to different factors like coating

method, construction tools, dilution ratio and flat performance of the coated surface).

l Surface drying time ≤4 hours(25°C,Relative humidity ≤85%)

l Recoat interval ≥8hours(25°C,Relative humidity ≤85%)

l Practical drying film thickness 120µm (Flat surface, coat once)

Packaging & Shipping

A component: 20 kg plastic drum

B component: 5 kg plastic drum

They should be stored under dry,shadow and cool place and the expiry date is 12 months under the normal temperature(20 °C/68 )

Storage

They should be stored under dry and cool place. The expiry date is 12 months under the normal temperature(20°C/68°F).

Guidance for Construction

l Construction Method

Roller coating

Brush coating

Spray coating

l Construction Tool

Rollers

Hairbrush

Airbrush

l Dilution method

Clear water(0-5%)

l Washing Way for Tool

Wash the tools immediately with clear water after construction.

l Conditions for Construction

The temperature of the wood or wall should not be lower than 8°C during the

construction, moisture content should be less than 10%, air humidity should not be

higher than 85%.

Treatment of Base Material

Before coating the wood, sand the surface of the wood evenly. Remove the impurity materials like dust and oil stain. Fill up the gaps between the wood with putty.

If the cement flooring or cement mortar flooring has been maintained for 4 weeks, sand the surface of the base material (flooring) evenly. Remove the dust, rust, oil stain and other impurity materials for 4 weeks protective. If there is crack or damage, mend it with the material that is the same as the base material. Then maintain it for at least one week.

Guidance for Construction Procedure

l For wood

Step one is to treat the surface of the wood.

Step two is to coat the waterborne high glossy epoxy varnish twice or more.

l For floor

Step one is to coat the surface paint.

Step two is to coat the waterborne glossy epoxy varnish once when the surface paint is dry.

Attention

l The rollers,brushes and other tools should be soaked into the water for about 5 minutes before constuction.

l Component A and B should be mixed correctly and stired evenly before construction. Choose the ratio of dilution according to the temperature and humidity. Viscosity should be made as the requirements. The mixture should be stired evenly and used after 15 minutes.

l Component A is waterbased coating which should not be polluted by organic solvents, component B should not be diluted by water.

l The mixed coating should be used in 1 hour, unfinished coating can’t be poured into the previous package. Otherwise, the thickening appears then the coating is useless.

l To protect the properties of the film, the coating should not be over-diluted no matter spary coating or roller coating.

l Put on safety equipment during the construction.

Safety Information

l Keep circulation of air during construction.

l Use protective masks, gloves and other protective tools to prevent skin or eyes from

absorbing excess paint mist.

l Wash eyes with plenty of water if they are contaminated, and see a doctor.

l Cover the lid of the products during the construction rest.

l Keep the products away from children.

The Markets Selling Our Products In The World

Company Information

Tianyi Chemical Engineering Material Co., Ltd,located in Shunde,Guangdong,China. Specializes in R&D, Application, Production and Sale of Matting agent, Fumed silica, Zinc stearate and Aqueous synthetic resins. We get approved ISO9001-2008 and all our chemicals owns Reach, ROHS certification.

We have set up “Powder chemicals R&D centers”, “Aqueous synthetic resin R&D center”, “Paint and ink applications R&D center ", “Paper and leather applications R&D center"successively.

The productive capacity of powder chemicals and aqueous synthetic resin get 40,000 tons and 80,000 tons annually.

Our chemicals are mainly exported to Europe (Italy, Russia), Mid-east (UAE,Turkey, Egypt,Pakistan), Southeast Asia (Indonesia,Vietnam,Thailand,Philippines), South America(Columbia,Venezuela,Ecuador,Chile), North America(Mexico), Africa(Ghana,Nigeria,Tunisia) and we do business with some multinationals like Varlspar and Sherwim-Williams.

We win high reputation and honesty from our customers because of excellent products performance. We strongly believe we are your best choice.