Summary:

SAKURAI ALINON MK - TC series of new non-silicon aluminum alloy mold release agent. Do not contain silicone oil, it is suitable for the aluminum alloy casting which have high demand on the surface condition and non-silicon simple die castings. Such as: auto parts, aviation products, household goods, etc. This product contains no HAP and PAHS, meets ROHS and REACH the latest environmental protection standard. Stripping performance is good, do not turn yellow, not stink. It is the latest best substitute of the silicon release agent.

Product features:

1. Easy for the subsequent processing.

SAKURAI non silicone release agent do not contain silicon, variegated stone, do not cause product surface silicon residue and heavy metal exceeds the standard, effectively avoid surface silicon penetration, painting peeling off, electroplating products blister and product surface viscose rayon falling out.

2. Excellent demolding performance

When SAKURAI aluminum alloy release mould spray is sprayed to the mould surface, its effective ingredients form dense film at once. The membrane in the injection process is high pressure resistant, scouring resistant, low friction coefficient, effectively prevents die-casting products to soldering with the mould. At the same time the excellent lubrication performance speeds up the flowing aluminum liquid, so that the aluminum liquid can rapidly form a mould.

3. Make the surface birght

SAKURAI release mould spray adopt rare and special materials. It can effectively solve the problems such as casting surface turns black, too much water lines and cold shut. Can solve the problems happening in postprocessing, such as: polishing and electroplating.

4. Protect the mold

SAKURAI release mould spray forms a protective film on the mould surface. Effectively reduce the heat for the mould and reduce the impact from the liquid aluminum to the machine. Correct selection of high quality mould release mould spray can effectively protect the mould , prolong the life of the mould and reduce the repair.

5. No carbon deposition on the mold surface

SAKURAI release mould spray is very easy to use. No carbon deposition, no in-cavity deposition , no mold scale and no oxide skin. Reduce the times to clean the mould, and if you use this release mould spray the product surface will be bright and clean, does not affect the subsequent spray plating, polishing and surface treatment.

6. Good cooling effect.

In die casting process because of the high temperature, mould has been heating ,the temperature of liquid metal rises, and the high mold temperature makes die casting defect. SAKURAI release mould spray effectively controls these problems .Such as: soldering, blistering, cracking, and burned.

7. High safety performance

SAKURAI release mould spray is non-toxic, non-flammable, no corrosion, no chemical reaction. In the process of use,no harmful smoke will appear.

Physical and chemical data:

Usage :

1. The recommended using dosage (dilution ratio) : general processing: 1:100 complex processing: 1:180, please finally determine the best dilution ratio according to test concentration deployed by the technology personnel!

2. If your usage will be excess the typical usage please contact us for technical support.

3. Mix with water after use (diluted concentrate liquid with the water ).

4. Please use deionized water to dilute, helping to prolong the life of working liquid, reduce the usage of concentrate , fully reflects the performance of the processing fluid.

5. Unless the technical services allow , do not add other material to concentrate and diluent.

6. The concentration of control may be achieved through the refractometer and refraction coefficient of diluent concentration percentage.

Notice:

1, Die-casting release mould spray must dilute with pure water, dilution ratio 1:80-1:100, and gently shake or stir when you use; Dilution ratio is appropriately adjusted according to the complexity of the casting and the depth of the mould.

2, Using the spray gun or automatic system to spray, pay attention to spray evenly and blow dry.

3, The best using temperature of the mould is 200 °C to 350 °C.

4, Die-casting mould release mould spray stored under normal temperature, pay attention to prevent frostbite prevent bask in, after opening pay attention to hermetic seal and store well.

Our office

Certificate

How to contact us?