MODEL

IPC-200

OUTPUT

OUTPUT NUMBER

CH1

CH2

CH3

CH4

CH5

CH6

DC VOLTAGE

3.3V

5V

12V

-5V

-12

5VSB

RATED CURRENT

15A

25A

13A

0.5A

1A

2A

CURRENT RANGE

0~15A

1~25A

1~13A

0~0.5A

0.1~1A

0~2A

RATED POWER NOTE.8,9

200W continue Combine power max:+5V,+3.3V,+12V output shall not exceed 180W max.(The+5&+3.3Volt combine total output shall not wxceed 150W)(The -5$-12Volt combine total output shall not exceed 12W)

RIPPLE & NOISE (max.) Note.2

50mVp-p

50mVp-p

120mVp-p

100mVp-p

120mVp-p

50m Vp-p

VOLTAGEADJ.RANGE

CH2:5.05~5.5V

VOLTAGE TOLERANCE Note.3

CH1:5.0%

5.0%

7.0%

8%

10%

5.0%

LINE REGULATION

1.0%

1.0%

1.0%

2.0%

2.0%

1.0%

LOAD REGULATION

5%

5%

7%

8%

10%

5.0%

SETUP, RISE TIME

800ms 20ms/230VAC 2500ms,20ms/115VAC at full load

HOLD UP TIME(TYP)

16ms/230VAC 16ms/115VAC at full load

INPUT

VOLTAGE RANGE

90 ~ 264VAC

FREQUENCY RANGE

47 ~ 63Hz

POWER FACTOR

EFFICIENCY (Typ.)

75%

AC CURRENT (Typ.)

3.5A/115VAC 1.7A/230VAC

INRUSH CURRENT (Typ.)

40A/115VAC 80A/230VAC

LEAKAGE CURRENT

3mA/240VAC

PROTECTION

OVER LOAD

105~150% rated output power

Protection type :Shut down o/p voltage,re-power on to recover

OVER VOLTAGE

+3.3V,+5V:110%~140% of rated voltage:+12V:13.2V~16V

Protection type :Shut down o/p voltage,re-power on to recover

SHORT CIRCUIT

All output equipped with short circuit

Protection type :Shut down o/p voltage,re-power on to recover

FUNCTION

POWER GOOD SIGNAL

The TTL compatible signal with 100~500ms delay after set up

POWER FALL SIGNAL

The TTL compatible signal with go down at least 1ms before +5V below 4.75V

PS-ON INPUT SIGNAL

Power ON:PS-ON=”Low”.or”>2V”;Power OFF:PS-ON=”Hi” .or”<1.5V”

ENVIRONMENT

WORKING TEMP.

-10~ +60 oC(Refer to output load derating curve)

WORKING HUMIDITY

20 ~ 90% RH non-condensing

STORAGE TEMP., HUMIDITY

-40 ~ +85 , 10 ~ 95% RH

TEMP. COEFFICIENT

0.05%/ oC(0 ~ 50 )

VIBRATION

10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes

SAFETY &EMC(Note 4)

SAFETY STANDARDS

UL60950-1,TUV EN60950-1 approved

WITHSTAND VOLTAGE

I/P-O/P:1.5KVAC I/P-FG:1.5KVAC

ISOLATION RESISTANCE

I/P-O/P:,I/P-FG,O/P-FG:50M Ohms/500VDC

EMI CONDUCTION & RADIATION

Compliance to EN55022 (CISPR22) Class B,Design refer to FCC part 15Class B

HARMONIC CURRENT

Compliance to EN61000-3-2,3

EMS

IMMUNITY

Compliance to EN61000-4-2,3,4,5,6,8,11;ENV50204,EB55024,EN61000-6-2(EN50082-2) heavy industry level, criteria A

OTHERS

MTBF

94.1Khrs min. MIL-HDBK-217F (25 )

CONNECTOR

ATX main power connector *1ea;+12V power cinnector *1ea

Peripheral power cinnector *3ea ;Floppy drive power connector *1ea

COOLING

Forced air ventilation by 4cm DC fan

DIMENSION

240*83*40mm (L*W*H)

PACKING

1.44Kg;10pcs/15.4Kg/0.89 CUFT

NOTE

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25°Cof ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.

5. Derating may be needed under low input voltages. Please check the static characteristics for more details.