MODEL

CLG-150-12

OUTPUT

DC VOLTAGE

12V

CONSTANT CURRENT REGION Note.4

9 ~ 12V

RATED CURRENT

11A

RATED POWER

132W

RIPPLE & NOISE (max.) Note.2

150mVp-p

VOLTAGE ADJ. RANGE Note.6

9 ~ 13V

CURRENT ADJ. RANGE

Can be adjusted by internal potentiometer A type and C type only

5.5 ~ 11A

VOLTAGE TOLERANCE Note.3

±2.0%

LINE REGULATION

±0.5%

LOAD REGULATION

±1.0%

SETUP, RISE TIME

3000ms, 80ms at full load 230VAC /115VAC

HOLD UP TIME (Typ.)

50ms / 230VAC 16ms / 115VAC at full load

INPUT

VOLTAGE RANGE Note.4

90 ~ 295VAC 127 ~ 417VDC

FREQUENCY RANGE

47~63HZ

POWER FACTOR (Typ.)

PF>0.98/115VAC, PF>0.95/230VAC, PF>0.93/277VAC at full load (Please refer to "Power Factor Characteristic" curve)

EFFICIENCY (Typ.)

88%

AC CURRENT (Typ.)

2A / 115VAC 1A / 230VAC 0.68A / 277VAC

INRUSH CURRENT (max.)

COLD START 65A(twidth=595us measured at 50% Ipeak) at 230VAC

LEAKAGE CURRENT

<1mA / 240VAC

PROTECTION

OVER CURRENT

95 ~ 108%

Protection type : Constant current limiting, recovers automatically after fault condition is removed

SHORT CIRCUIT

Hiccup mode, recovers automatically after fault condition is removed

OVER VOLTAGE

13.5 ~ 16V

Protection type : Shut down and latch off o/p voltage, re-power on to recover

OVER TEMPERATURE

100°C±10°C (RTH2)

Protection type : Shut down o/p voltage, re-power on to recover

ENVIRONMENT

WORKING TEMP.

-30 ~ +70°C(Refer to "Derating Curve")

WORKING HUMIDITY

20 ~ 95% RH non-condensing

STORAGE TEMP., HUMIDITY

-40 ~ +80°C, 10 ~ 95% RH

TEMP. COEFFICIENT

±0.03%/°C (0 ~ 50°C)

VIBRATION

10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes

SAFETY&EMC

SAFETY STANDARDS

UL8750, CSA C22.2 No. 250.0-08, UL1012, CAN/CSA-C22.2 No. 107.1-01, EN61347-1, EN61347-2-13 independent

(except for CLG-150 C type), UL60950-1, TUV EN60950-1,IP65 or IP67, J61347-1(option, except for CLG-150 C type), J61347-2-13 approved

WITHSTAND VOLTAGE

I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC

ISOLATION RESISTANCE

I/P-O/P:100M Ohms / 500VDC / 25°C/ 70% RH

EMC EMISSION

Compliance to EN55015, EN55022 (CISPR22) Class B, EN61000-3-2 Class C (≥75% load) ; EN61000-3-3

EMC IMMUNITY

Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547, EN55024, light industry level (surge 4KV), criteria A

QTHERS

MTBF

303.7K hrs min. MIL-HDBK-217F (25°C)

DIMENSION

222.2*68*38.8mm (L*W*H)(CLG-150-Blank/A/B) 229*68*38.8mm (L*W*H)(CLG-150-C)

PACKING

1.0Kg; 12pcs/13Kg/0.58CUFT(CLG-150-Blank/A/B) 1Kg; 12pcs/13Kg/0.96CUFT(CLG-150-C)

NOTE

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25°C of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance: includes set up tolerance, line regulation and load regulation.

4. Constant current operation region is within 75% ~100% rated output voltage. This is the suitable operation region for LED related applications, but please reconfirm special electrical requirements for some specific system design.

5. Derating may be needed under low input voltages. Please check the static characteristics for more details.

6. A type and C type only.

7. Safety and EMC design refer to EN60598-1, subject 8750(UL), CNS15233, GB7000.1, FCC part18.

8. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.